All tools
TOOL IDB-MEC-002
Snap-fit stress

Desktop only

Engineering tools are available only on desktop screens.

Snap-fit stress

Peak bending strain on a rectangular cantilever snap during assembly. Compare against the resin's allowable strain — if you exceed it, the hook breaks on first install.

Cantilever beam — deflection ε = —
δ L = 15 mm h
Engineering notes

Formula (rectangular cantilever)

  • εmax = 1.5 · h · δ / L²
  • σ = E · ε

Sanity rules

  • One-time assembly: ε < 70% allowable.
  • Reusable snap: ε < 40% allowable.
  • Taper the beam for more uniform stress — tip strain drops 30–50%.
  • Round the inside corner where snap meets housing.

How the calculation works

The hook is modelled as a straight cantilever beam with a constant rectangular cross-section, fixed at the root and deflected at the tip. When the hook rides over the catch, the tip deflects by δ, and the peak bending strain at the root surface is ε = 1.5 · h · δ / L², where h is the beam thickness in the direction of deflection and L is the beam length. The beam width does not affect strain, because a wider beam is stiffer but strains the same amount for the same deflection.

Stress is estimated as σ = E · ε, using the material's elastic modulus. The tool then divides the peak strain by the material's allowable strain for a single assembly. A utilisation above 100% means the hook is expected to break on assembly. Between 70% and 100% the hook should survive one assembly but should not be reused. Between 40% and 70% it suits occasional reuse, and at 40% or less it suits frequent reuse.

The model assumes small deflections, a rigid root and no stress concentration. A sharp inside corner at the root can raise the local strain well above the calculated value. The forces assume a rectangular section of width b, and none of the results account for creep, temperature, moisture or glass fibre content. Above the proportional limit, σ = E · ε overestimates the real stress in plastics, and the forces with it.

Worked example

Inputs: beam length L = 15 mm, thickness h = 1.5 mm, deflection δ = 0.8 mm, material PC/ABS with E = 2400 MPa and allowable strain 2.2%. These are the tool's default values.

  1. L² = 15 × 15 = 225 mm².
  2. ε = 1.5 × 1.5 × 0.8 / 225 = 1.8 / 225 = 0.0080, which is 0.80%.
  3. σ = 2400 MPa × 0.0080 = 19.2 MPa.
  4. Utilisation = 0.80% / 2.2% = 0.36, which is 36%.

Result: the peak strain of 0.80% uses 36% of the allowable strain, which is below the 40% limit, so the tool rates the hook as suitable for frequent reuse. There is room to shorten the beam or increase the deflection if a stronger catch is needed.

Frequently asked questions

What strain is allowed for a PC snap-fit?

This tool uses 2.5% as the single-assembly allowable strain for unfilled polycarbonate. With the 40% reuse rule, that means about 1.0% for a hook that is assembled many times. Allowable strain depends on the grade, colour additives, temperature and moisture, so check the resin supplier's design data for your exact grade before you freeze the design.

How can I reduce the strain in a snap-fit hook?

Strain falls with the square of the beam length, so doubling L reduces strain to one quarter. Halving the thickness halves the strain, and so does halving the deflection. A beam that tapers to a thinner tip spreads the strain more evenly along its length. A generous root radius reduces the local peak strain, which this simple formula does not show.

Why does the tool check strain instead of stress?

Most thermoplastics have a non-linear stress-strain curve, so a stress limit taken from a datasheet does not describe behaviour well near failure. Strain limits are easier to measure and are what resin suppliers usually publish for snap-fit design. The stress value shown here is a linear estimate and is mainly useful for comparing designs.

How do I estimate the assembly force?

For a rectangular cantilever, the deflection force at the tip is P = b · h² · E · ε / (6 · L), where b is the beam width. The insertion force along the push direction is W = P · (μ + tan α) / (1 − μ · tan α), where α is the lead-in angle and μ the friction coefficient. The tool computes both from the width, angle and friction you enter; when μ · tan α reaches 1 the hook self-locks and cannot be pushed in.

Result

Live