All tools
TOOL IDB-MEC-007
ISO 286 fit calculator

Desktop only

Engineering tools are available only on desktop screens.

Please open this page on a laptop or desktop browser.

ISO 286 hole and shaft tolerance calculator

Hole + shaft tolerances per ISO 286. Identifies the diameter step, applies the IT grade and fundamental deviation, returns part limits and clearance / interference.

Hole & shaft fit H7 / g6
Engineering notes

Sources

  • Local ISO 286 fundamental tolerance tables transcribed for the supported diameter range.
  • Use for engineering planning and verify final production drawings against the controlled standard.

How the calculation works

The calculator does not derive tolerances from formulas. It finds the nominal size step that contains your diameter, using the ISO 286 convention "over a, up to and including b", so 30 mm belongs to the >18–30 mm step and 30.01 mm to the >30–40 mm step. It then reads the upper and lower limit deviations for each selected class directly from the ISO 286-2 tables, in micrometres. For the hole these are ES and EI, for the shaft es and ei.

Each part limit is the nominal size plus the deviation divided by 1000. Minimum clearance is the smallest hole minus the largest shaft, and maximum clearance is the largest hole minus the smallest shaft. If both values are zero or positive the fit is a clearance fit, if both are zero or negative it is an interference fit, and otherwise it is a transition fit. The JS and js classes are symmetric zones of ±IT/2 and are computed exactly from the IT grade, which can give half-micrometre values.

The tables cover nominal sizes above 3 mm and up to 400 mm. A class that is not tabulated for a given size is reported as unsupported instead of being estimated. The tool does not account for thermal expansion, form and position errors, surface roughness, plating thickness or the press force needed for an interference fit.

Worked example

Inputs: nominal diameter 90 mm, hole class H7, shaft class g6. These are the tool's default values.

  1. 90 mm falls in the >80–100 mm size step, where IT7 = 35 µm and IT6 = 22 µm.
  2. Hole H7: EI = 0 µm and ES = +35 µm, so the hole measures 90.000 mm to 90.035 mm.
  3. Shaft g6: es = −12 µm and ei = −34 µm, so the shaft measures 89.966 mm to 89.988 mm.
  4. Minimum clearance = 90.000 − 89.988 = 0.012 mm.
  5. Maximum clearance = 90.035 − 89.966 = 0.069 mm.

Result: a clearance fit with 12 µm to 69 µm of diametral clearance. Even the tightest combination of parts leaves a small gap, so the shaft can rotate or slide in the bore. H7/g6 is typically used as a precise sliding or locating fit.

Frequently asked questions

What is the difference between H7/g6 and H7/h6?

Both are clearance fits, but h6 has its upper deviation at zero, while g6 is shifted below the nominal size. At 25 mm, H7/g6 gives 7 µm to 41 µm of clearance and H7/h6 gives 0 µm to 34 µm. H7/h6 can therefore assemble with zero clearance and suits locating parts that do not move. H7/g6 always keeps a small gap and suits parts that must slide or rotate.

Which fit should I use for a press fit?

For a hole-basis press fit, H7/p6 is a common choice. At 25 mm, H7 is 0/+21 µm and p6 is +22/+35 µm, which gives an interference of 1 µm to 35 µm. Heavier fits such as H7/r6 give more interference. Always check the resulting hub stress and the press force separately, because this calculator does not compute them.

What is a transition fit?

A transition fit can produce either clearance or interference, depending on where the actual parts fall inside their tolerance zones. For example, H7/k6 at 25 mm ranges from 15 µm of interference to 19 µm of clearance. Transition fits are used where accurate location matters and light pressing or tapping during assembly is acceptable, for example for gears or couplings that are keyed to a shaft.

What does the IT grade mean?

The IT grade sets the width of the tolerance zone, and the letter sets its position relative to the nominal size. A lower number means a tighter tolerance. At 25 mm, IT6 is 13 µm and IT7 is 21 µm. Grades 6 and 7 are typical for precision machined fits, while grades 11 and above are normal for coarse or non-mating features.

Why is my diameter rejected?

The tool only covers the ISO 286-2 table range, which is above 3 mm and up to 400 mm. Diameters of 3 mm or less, and above 400 mm, are outside the dataset and are not extrapolated. Classes tabulated for only part of the range are reported as not available outside it.

Result

Calculate